I got a vr with one pin up, 2 down.
solder pin 1 on to card, pin 2 (left one if vr is down with the 2 pins).
Now i measure 0,40kohm from pin one to pin 2.
So, I'm ok ?

Do you increase voltage when in windows ?
When I increase voltage above 1.5, I get a freeze ?

So if you have only 0.4 resistence between pin 1 and 2, you mustn't solder those pins. Otherwise, you'll burn the card.

(Ps.: be sure to measure the resistence BEFORE you solder to the chip!)

you got a photo of your VR gamer?

Vmod works, only when going above 1.7v it goes fast, a mm = 0,5v more.

This IS the max I can get out of it on stock cooling.
Your turn Troman, Blind and all you people out there : |D |D |D |D

http://service.futuremark.com/compare?2k1=9220694

:ws: :ws:

I'm the master of this competition... :naughty:

nice one:) and I see you switched drivers:) what cooling do you have on the 7300GT?

Still stock cooler.

good to know:)

I was supprised it can take that amount of heat, vgpu 1.8.
Just some extra coolers.

It must be a supercard :)

holy poop! The old man knows how to OC!

getting close to world record (907/1066)
http://www.hwbot.org/searchResults.d...nts=&limit=200

small error :p

^^

http://service.futuremark.com/compare?2k1=9227277

Hello boy's, I'm baaaaaaaaack :)



Was done @ 3000mhz flat, still got that problem with wrong CPU speed.
No screen, sorry, got a BSOD after saving result :(
system doesn't boot anymore, don't know what happend.

Phase change, I guess?

very nice OC, if you run at max CPU speed with default settings you will get nice HWBot score:)

what cooling ?

chilly1 unit I guess ;)

no guessing allowed:) we want certainty ;)

FM orb down?

yup

Yes, that Chilly one unit.
But, I guess it's faulty.
Just used it twice now for about 10 minutes, and the card already gives positive temperatures.
So, my guess is, unit is loosing gas somewhere.

933 is kinda low core speed :/

at dryice 1ghz was possible with ease...

You should easy do some 975 runs ^^

|D hum hum |D

Not possible I guess.
Can I see your result Troman ?

hum hum what? never said you told it wrong; just said that "guessing" it doesn't add value:p

http://service.futuremark.com/compare?2k1=9227541
Only pencilmod on mem.
Hardmod realy needed here, hopefully I don't break this gem.

Check CPU speed :p

multiplier detection fault by FM ;)

Pics of the setup ( and mounting :) ) pls.

in combi met 4.5~5Ghz CPU had je 1st spot:)
http://www.hwbot.org/result.do?resultId=623378

I know, only this cpu is already tested on Dice, and it did 4500mhz.
Phase change should get it to 4300 mhz, I hope :)

Seems like the orb is down again, did some 03 benching on an empty stomach :p
taking back 2 spots for the team.

at what voltage?

lods?

same voltage as before :)
I need a hardmod on the mem.
1.85v on GPU.
Didn't check the ramvoltage, but it shouldn't be much more than stock.
Oh, I got 19551 on 3D03, second spot on hwbot.
Taking first shouln't be difficult :)

it did more then 4.5ghz ^^

Good, we need points these days ... no top 15 anymore :(

Submited.
You gained a spot there :)

we gained two places today ;)

yeah, thanks :p

got some pics of your subzero setup?

not yet, will post in a few day's, sorry.

I don't get it, CPU can only do 4250 on phase.
I guess my mounting isn't correct :(

Just uped my points on HWbot, look at first result on 03, what are the odd's :)

setup.

Prommie on cpu?