LanCool PC-K58 ATX Mid Tower Case Review

jmke · 28th December 2009, 14:04

Take all the engineering talent of Lian-Li, use it to make an affordable yet feature rich product and you end up with the LanCool PC-K58. We take this budget friendly mid size tower case for a spin and compare its performance to several competitors. Does a 140mm in-take pay off? First tool-less PSU installation worthless? Read more to find out.

http://www.madshrimps.be/gotoartik.php?articID=978

30th December 2009, 07:10

I noticed that special Lian Li fan screws have to be purchased if you want to install a 140mm fan on the roof of the case. Do you know if the silicone/rubber standoffs that come with some fans (Noctua, Gelid, Nexus) can be used instead of these Lian Li screws?

jmke · 30th December 2009, 07:47

unfortunately no, those kind of rubber stand offs are completely different

those needed for this case are custom:

30th December 2009, 15:47

That's too bad. Lian Li should of included those fan screws with the PC-K58, because I can't find them sold at any store in Canada.

Then again, some users might not use it and it would be a waste of material.

I guess end users will have to contact Lian Li if they want some, but can't find it at any store. A bit tedious.

Thank for the reply mate

28th December 2009, 14:04	#1
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 79,021	LanCool PC-K58 ATX Mid Tower Case Review Take all the engineering talent of Lian-Li, use it to make an affordable yet feature rich product and you end up with the LanCool PC-K58. We take this budget friendly mid size tower case for a spin and compare its performance to several competitors. Does a 140mm in-take pay off? First tool-less PSU installation worthless? Read more to find out. http://www.madshrimps.be/gotoartik.php?articID=978 __________________

30th December 2009, 07:47	#3
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 79,021	unfortunately no, those kind of rubber stand offs are completely different those needed for this case are custom: __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Tagan CS-EL Diablo Mid Tower ATX Case	jmke	WebNews	1	4th May 2011 17:07
Aerocool PGS Vs-9 Mid Tower Case Review	jmke	WebNews	0	13th July 2010 13:34
[M] LanCool PC-K58 ATX Mid Tower Case Review	jmke	WebNews	1	28th December 2009 14:05
NZXT Gamma Mid Tower Case Review	jmke	WebNews	0	28th December 2009 08:15
Cooler Master Elite 310 Mid Tower Case Review	jmke	WebNews	0	16th December 2009 10:05
LanCool Dragon Lord PC-K62 Advanced Mid Tower Case	jmke	WebNews	0	24th September 2009 09:28
AeroCool S9 Pro Mid Tower Case Review	jmke	WebNews	0	17th November 2008 12:04
Apevia X-Sniper G-Type Mid Tower Case Review	jmke	WebNews	0	28th August 2008 12:01
Thermaltake Armor+ MX VH8000BWS Mid Tower ATX Case Review	jmke	WebNews	0	20th August 2008 12:07
Antec New Solution Series NSK6500 Super Mid Tower ATX Case	jmke	WebNews	0	22nd August 2006 09:22

30th December 2009, 07:10	#2
SirMango Posts: n/a	I noticed that special Lian Li fan screws have to be purchased if you want to install a 140mm fan on the roof of the case. Do you know if the silicone/rubber standoffs that come with some fans (Noctua, Gelid, Nexus) can be used instead of these Lian Li screws?

30th December 2009, 15:47	#4
SirMango Posts: n/a	That's too bad. Lian Li should of included those fan screws with the PC-K58, because I can't find them sold at any store in Canada. Then again, some users might not use it and it would be a waste of material. I guess end users will have to contact Lian Li if they want some, but can't find it at any store. A bit tedious. Thank for the reply mate