 |  |  |  |  |
Jort Phase change
| |||||||||
|
Jort Phase change
| | |||||||
 |
 |
| | Thread Tools |
19th November 2012, 18:09
| #1 |
| [M] Reviewer  Join Date: Dec 2008
Posts: 3,024
  |  Jort Phase change lo Jort , Phase unit schakelt zich om de haverklap uit, soms werkt ie 10 minuten en dan ineens valt ie zich weer uit. Soms start ie ook niet door ( als hij de PSU zoekt ) Hoe koppel ik die compressor rechtstreeks aan de elektriek zonder dat stuurmoduletje te gebruiken ? Hier ne foto van de setup : 
__________________  |
|
|
19th November 2012, 19:14
| #2 |
| OCTB Crew  Join Date: Jun 2004 Location: mechelen(belgium)
Posts: 2,037
 | Moeilijk zo te zeggen maar is zo te horen een electronisch probleem. Om rechtstreek aan te sluiten zou je een foto kunnen nemen van het zwarte kapje van de compressor?
__________________ watercooling, chilled water,direct phase change, cascade, custom modding |
|
|
|
19th November 2012, 19:20
| #3 |
| [M] Reviewer Join Date: Dec 2008
Posts: 3,024
| zwarte kapje ?
__________________ |
|
|
|
21st November 2012, 23:55
| #4 |
| OCTB Crew Join Date: Jun 2004 Location: mechelen(belgium)
Posts: 2,037
| Idd. De andere kant vd compressor.
__________________ watercooling, chilled water,direct phase change, cascade, custom modding |
|
|
|
22nd November 2012, 22:37
| #5 |
| [M] Reviewer Join Date: Dec 2008
Posts: 3,024
|  
__________________ |
|
|
|
15th December 2012, 09:56
| #6 |
| [M] Reviewer Join Date: Dec 2008
Posts: 3,024
|   
__________________ |
|
|
|
17th December 2012, 08:51
| #7 |
| OCTB Crew Join Date: Jun 2004 Location: mechelen(belgium)
Posts: 2,037
| Hellow, You have to disconnect the black wire with the red thinghy on, and connect the brown wire coming from the powercord to the contact that you disconnect. I don't now that you have that flat connector ? if nog you can cut it and connect with an " lusterklem"  easy hu 
__________________ watercooling, chilled water,direct phase change, cascade, custom modding |
|
|
|
17th December 2012, 17:51
| #8 |
| [M] Reviewer Join Date: Dec 2008
Posts: 3,024
|  1) zwarte kabel met rode sleeving afkoppelen 2) maakt het verschil uit welke bruine kabel ik eraan hang ( 2 of 3 ) 3) koppel ik de beide doosjes af ? Dus enkel rechtstreeks op de power kabel ?
__________________ Last edited by leeghoofd : 17th December 2012 at 19:39. |
|
|
|
17th December 2012, 21:58
| #9 |
| OCTB Crew Join Date: Jun 2004 Location: mechelen(belgium)
Posts: 2,037
| er komt toch maar 1 bruine kabel uit de witte powerkabel ? al de rest mag je gewoon laten, maakt normaal niet uit
__________________ watercooling, chilled water,direct phase change, cascade, custom modding |
|
|
|
17th December 2012, 23:21
| #10 |
| [M] Reviewer Join Date: Dec 2008
Posts: 3,024
| K thx morgen testen dus
__________________ |
|
|
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Phase change building and modding by Jort | jort | Air - Water - Peltier - Phase Change - LN2 Cooling Projects | 33 | 10th June 2011 09:18 |
| Project Phase change chiller | jort | Air - Water - Peltier - Phase Change - LN2 Cooling Projects | 3 | 9th May 2011 13:21 |
| Phase Change Cooling ,which is the best | GoldenEye | Air - Water - Peltier - Phase Change - LN2 Cooling Projects | 51 | 22nd February 2008 10:32 |
| own made phase-change project | jort | Air - Water - Peltier - Phase Change - LN2 Cooling Projects | 28 | 11th July 2004 23:24 |
| Tripple Phase change Rig | jmke | WebNews | 4 | 11th July 2004 22:25 |
| Basic phase-change set up walkthrough | jmke | WebNews | 4 | 28th April 2004 21:05 |
| phase change <--> cascade phase change? | kristos | General Madness - System Building Advice | 20 | 2nd March 2004 09:30 |
| Dual Phase-Change Cooling | jmke | WebNews | 1 | 18th December 2003 11:20 |
| Phase Change this! Mach I | jmke | Hardware Overclocking and Case Modding | 64 | 8th July 2003 13:20 |
| Thread Tools | |
| |
