Vantec Iceberq4 Pro (modem warning)

6th October 2003, 16:58

1st review @ the [M], 1st ever for that matter.
Today I'll be looking at the vantec Iceberq 4 Pro chipset / graphics heatsink fan combo. Intended for use on GeForce4 Ti and FX5600 based graphics cards.
The packaging was nothing special, almost default retail kit. The manual (install guide) was a full 2 pages long. Not that anyone interested in this product should need anymore (anything?).

To begin some specs:
45*10mm ball bearing fan, rotating 5500RPM @12V pushing 8.6CFM drawing 1.98W.
The heatsink is copper wheighing in at 87g, with a total dimension of 88*65*15mm.
Also included are 4 small "memory" heatsinks 20*20*6mm large, typical aluminium extrusion design.
4 plastic pushpins, some generic white goop and 4 pieces of 3M "thermal-tape" complete the package. Only 2 pushpins are needed to install, and this redundancy is appreciated, I usually use screws anyway since thise things wear fast. Some extra pieces of fragtape would have been nice also.

The memsinks are nothing special, default alu extrusion as said before. A good lapping should do some good, these things tend to hollow as they cool down. Bottom is fairly smooth however.
The cooling unit itself is worth a closer look. The heatsink is 100% copper, with a mirror finish on the bottom. The fins are either carefully soldered on it, or are glued. They cleaned it up so good it's hard to see. The fan is screwed dead center onto the bottom plate. This means there isn't a lot of dissapation surface right on top of the heatsource. The copper should spread the heat out quickly however.

So, this concludes the first part of the revieuw. More of a previeuw, but there'll be more soon.
I originally needed a new chipset heatsink for my epox 8RDA+. I knew that the mounting holes of a Radeon are too close together, and a GF4 cooler are too far apart. Meaning I'll have to mod it first, if I want to make it fit the epox.
Up next, modding and placement...
(damn gotta shut the PC down for this)

jmke · 6th October 2003, 17:27

great start, hopefully the full copper will do the necessary job!

The Senile Doctor · 25th October 2003, 23:16

and ...
what did it do???

26th October 2003, 10:18

not using it, putting holes in it on the good distance for my norce would be too much of a pain. I'll have a test og a GF4 if I can get my hands on one.

Getting a titan CUV2AB tomorrow for NB cooling. That should fit.

6th October 2003, 16:58	#1
FreeStyler Posts: n/a	1st: Vantec Iceberq4 Pro (modem warning) 1st review @ the [M], 1st ever for that matter. Today I'll be looking at the vantec Iceberq 4 Pro chipset / graphics heatsink fan combo. Intended for use on GeForce4 Ti and FX5600 based graphics cards. The packaging was nothing special, almost default retail kit. The manual (install guide) was a full 2 pages long. Not that anyone interested in this product should need anymore (anything?). To begin some specs: 4510mm ball bearing fan, rotating 5500RPM @12V pushing 8.6CFM drawing 1.98W. The heatsink is copper wheighing in at 87g, with a total dimension of 886515mm. Also included are 4 small "memory" heatsinks 2020*6mm large, typical aluminium extrusion design. 4 plastic pushpins, some generic white goop and 4 pieces of 3M "thermal-tape" complete the package. Only 2 pushpins are needed to install, and this redundancy is appreciated, I usually use screws anyway since thise things wear fast. Some extra pieces of fragtape would have been nice also. The memsinks are nothing special, default alu extrusion as said before. A good lapping should do some good, these things tend to hollow as they cool down. Bottom is fairly smooth however. The cooling unit itself is worth a closer look. The heatsink is 100% copper, with a mirror finish on the bottom. The fins are either carefully soldered on it, or are glued. They cleaned it up so good it's hard to see. The fan is screwed dead center onto the bottom plate. This means there isn't a lot of dissapation surface right on top of the heatsource. The copper should spread the heat out quickly however. So, this concludes the first part of the revieuw. More of a previeuw, but there'll be more soon. I originally needed a new chipset heatsink for my epox 8RDA+. I knew that the mounting holes of a Radeon are too close together, and a GF4 cooler are too far apart. Meaning I'll have to mod it first, if I want to make it fit the epox. Up next, modding and placement... (damn gotta shut the PC down for this)

6th October 2003, 17:27	#2
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 79,021	great start, hopefully the full copper will do the necessary job! __________________

25th October 2003, 23:16	#3
The Senile Doctor Member Join Date: May 2002 Location: wherever the doom is Posts: 3,171	and ... what did it do??? __________________ OC-2-the-death Where the Reverend is doing his Magick, all mortals be silent Doom over the world

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cooler Master Introduces Silent Pro Gold PSU	jmke	WebNews	0	1st June 2010 14:59
Cooler Master Raises the Wattage on Silent Pro M with 850W and 1000W	jmke	WebNews	0	10th September 2009 08:17
QNAP Unveils Intel Core 2 Duo, 8-bay, 16TB iSCSI NAS - TS-809 Pro	jmke	WebNews	0	16th February 2009 11:25
QNAP TS-509 Pro Turbo NAS Released, Tested	jmke	WebNews	0	21st November 2008 11:13
Vantec Iceberq 4 Pro	jmke	WebNews	0	25th July 2004 21:59
ATI RADEON X800 PRO Makes Retail Debut in Japan, USA	jmke	WebNews	0	12th May 2004 14:50
ATI Extends Industry Lead in Integrated Graphics with RADEONTM 9100 PRO IGP	jmke	WebNews	0	3rd May 2004 13:10
VisionTek First to Deliver 9800 PRO 256MB	jmke	WebNews	0	14th May 2003 20:18

26th October 2003, 10:18	#4
FreeStyler Posts: n/a	not using it, putting holes in it on the good distance for my norce would be too much of a pain. I'll have a test og a GF4 if I can get my hands on one. Getting a titan CUV2AB tomorrow for NB cooling. That should fit.