OCZ DDR Booster + Asus P4C800

jmke · 16th October 2004, 15:00

I installed the DDR booster in my P4 board, plugged in the some BH-6 Mushkin, booted up the PC. I'm getting no display from the LEDs on the unit; however they did work on my MSI K8N Neo motherboard.

so I start to increase the FSB, which stops at ~220 CL2 2-2-5. I then turn the dial on the DDR booster to the right side, but since I have no readout, I have no idea how much voltage I'm feeding those chips. I stop halfway and try again.. memory now runs stable @ speed and timings seen below.

any utility which allows me to read the DDR voltages from Windows ?

kristos · 16th October 2004, 15:35

not that I know off,

hipro5's ddr "optimizer" or what does he call it will have Vdimm tracking but untill it's out and untill you get one for review (hint

) you could try and see if the normal reading points do the trick:

jmke · 16th October 2004, 15:36

don't have a voltmeter

but thanks for the pic

edit: dug up an old vmeter, it works

it's not very accurate but I was able to calibrate it to 3.0v

thanks Kristos

jmke · 16th October 2004, 15:49

really should get a digital voltmeter

kristos · 16th October 2004, 15:54

gentlemen, start your engines !!

250fsb 2-2-2-5 @ 3V

sweet

Sidney · 16th October 2004, 15:59

Your dial volt meter meeting 2004 technology reminds me of a grand father talking to his grand kid.

How lovely? they do seem to communicate well with each other.

wutske · 16th October 2004, 16:06

Try MBM (or speedfan or whatever you prefer), because sometimes it read your VMem (like it does on my mb)

jmke · 16th October 2004, 16:31

actually need 3.3+ for 250 CL2

MBM5 does not read vmem on Asus

Sidney · 16th October 2004, 17:14

Any comparison!

When you get a chance show 2-2-2-5 vs 3-4-4-8 (p4), please.

jmke · 16th October 2004, 17:44

the cause could be the -5V line missing from ATX connector on Coolermaster RP450w

16th October 2004, 15:00	#1
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 82,497	OCZ DDR Booster + Asus P4C800 I installed the DDR booster in my P4 board, plugged in the some BH-6 Mushkin, booted up the PC. I'm getting no display from the LEDs on the unit; however they did work on my MSI K8N Neo motherboard. so I start to increase the FSB, which stops at ~220 CL2 2-2-5. I then turn the dial on the DDR booster to the right side, but since I have no readout, I have no idea how much voltage I'm feeding those chips. I stop halfway and try again.. memory now runs stable @ speed and timings seen below. any utility which allows me to read the DDR voltages from Windows ? __________________

16th October 2004, 15:35	#2
kristos Member Join Date: Jan 2004 Posts: 1,554	not that I know off, hipro5's ddr "optimizer" or what does he call it will have Vdimm tracking but untill it's out and untill you get one for review (hint ) you could try and see if the normal reading points do the trick: __________________ "Welcome to the internet; where men are men, women are men, and little girls are FBI agents."

16th October 2004, 15:36	#3
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 82,497	don't have a voltmeter but thanks for the pic edit: dug up an old vmeter, it works it's not very accurate but I was able to calibrate it to 3.0v thanks Kristos __________________

16th October 2004, 15:49	#4
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 82,497	really should get a digital voltmeter __________________

16th October 2004, 15:54	#5
kristos Member Join Date: Jan 2004 Posts: 1,554	gentlemen, start your engines !! 250fsb 2-2-2-5 @ 3V sweet __________________ "Welcome to the internet; where men are men, women are men, and little girls are FBI agents."

16th October 2004, 15:59	#6
Sidney [M] Reviewer Join Date: Mar 2004 Posts: 16,730	Your dial volt meter meeting 2004 technology reminds me of a grand father talking to his grand kid. How lovely? they do seem to communicate well with each other. __________________ lazyman Opteron 165 (2) @2.85 1.42 vcore AMD Stock HSF + Chill Vent II

16th October 2004, 16:06	#7
wutske Member Join Date: May 2003 Location: Apenland Posts: 2,069	Try MBM (or speedfan or whatever you prefer), because sometimes it read your VMem (like it does on my mb) __________________ /me = Hardfreak My Blog: [W]eblog

16th October 2004, 16:31	#8
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 82,497	actually need 3.3+ for 250 CL2 MBM5 does not read vmem on Asus __________________

16th October 2004, 17:14	#9
Sidney [M] Reviewer Join Date: Mar 2004 Posts: 16,730	Any comparison! When you get a chance show 2-2-2-5 vs 3-4-4-8 (p4), please. __________________ lazyman Opteron 165 (2) @2.85 1.42 vcore AMD Stock HSF + Chill Vent II

16th October 2004, 17:44	#10
jmke Madshrimp Join Date: May 2002 Location: 7090/Belgium Posts: 82,497	the cause could be the -5V line missing from ATX connector on Coolermaster RP450w __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OCZ DDR Booster Mod	Sidney	WebNews	1	23rd September 2005 09:10
OCZ DDR Booster	Sidney	WebNews	0	2nd June 2005 14:14
Modding and Improving the OCZ DDR Booster for DFI, Chaintech, ETC, with 3 Ram Slots	jmke	WebNews	0	23rd December 2004 19:21
OCZ DDR Booster Review	Da_BoKa	WebNews	0	17th November 2004 13:34
OCZ DDR Booster Diagnostic Device	jmke	WebNews	0	24th October 2004 18:42
In-House: OCZ DDR Booster Review	jmke	WebNews	0	26th September 2004 23:05
OCZ DDR Booster Diagnostic Device	Sidney	WebNews	2	13th September 2004 15:23
OCZ DDR Booster Review: Overclockers' Dream	jmke	WebNews	0	11th August 2004 09:34
OCZ DDR Booster Reviewed @ VR-Zone Hardware	Sidney	WebNews	0	9th August 2004 01:45
OCZ DDR Booster Review	jmke	WebNews	0	25th July 2004 23:16