| ||Thread Tools|
|24th May 2009, 22:27||#62|
Join Date: Dec 2008
Try to play with the MCH reference voltage eg 0.74 or so and memtest ya rig before entering windows ( a few passes of test 7 will determine if it will survive Pi or not )
FSB = CPU Term...
Which CPU Skew and NB Skew ?
Does that ram really need 2.48 ?
Are you runing sync or not ?
Which PL selected ?
With fine tweaking 580-590FSB on air should be doable... not with 10 multi ofcourse
George did a good review on it :
Last edited by leeghoofd : 24th May 2009 at 22:32.
|24th May 2009, 22:38||#63|
I try booting into windows at 520-530 now, and using the EasyTune tool I can run SPi 1M at each step of the FSB. Memtest might indeed give me a stability-test, but do I need that? If it's SPi 1M-stable it's okay...
CPU and NB-skew: 100ps
The RAM-voltage is that high in that screnshot as I was testing if that was holding me back. Now it's at 2.4V. It's cooled very wel (2x120mm) and has D9GMH or D9GKX-chips on it. EPP-profile shows 2.2V and other manufacturers have those chips with an EPP of 2.4V...
What do you mean with sync or not? Mem-divider is 2.00B (B = 333MHz-strap)
Performance Level is at the middle of the three options. If the options are standard-turbo-extreme, it's at turbo. But I don't know the name of the setting by heart.
Considering all those questions and no more comment on the Vmch: can I conclude 1.4V with the massive heatsink is okay?
I hope to do 580-590FSB
|24th May 2009, 22:44||#64|
Besides: there's quite a difference between what you set in the BIOS and what's shown in the easytune-utility. I read that a lot on forums, but I don't know what voltages exactly differ...
|25th May 2009, 07:42||#65|
Join Date: Nov 2004
First, try to figure out what's the maximum FSB with a lower multiplier. If it's higher than 545, you know the cpu is holding you back.
|25th May 2009, 17:06||#67|
Join Date: Dec 2008
Try CPU at 200 and NB at 100 Skew ( never the same )
Memtesting with test 7, if it passes you can bench for sure at them speeds ( Pi and 3dmarks without an issue)
Ram PL is TRD in the Giga bios ( I believe ) Leave CPU and PCI Clock drive at AUTO (didn't need to move that setting at 580FSB Hyperpi stable)
Easytune readout is borked , there was a workaround but I never tried it, I'm a boot from bios guy , I loath windows utils...
580FSB shouldn't pose a prob
This is with the EP45T UD3P (DDR3 version)
|Thread||Thread Starter||Forum||Replies||Last Post|
|[M] MSI Master Overclocking Arena 2010 Benelux Final||jmke||WebNews||1||31st May 2010 17:16|
|MSI Master Overclocking Arena 2009 Grand Final in Beijing - Video Coverage||jmke||WebNews||0||6th September 2009 08:45|
|MSI Master Overclocking Arena 2008 Promo Video||jmke||WebNews||2||14th June 2009 15:37|
|MSI US Announces 2009 Product Lineup||jmke||WebNews||0||6th January 2009 08:17|
|MSI Master Overclocking Arena 2008 video||jmke||WebNews||0||12th November 2008 20:37|
|MSI Master Overclocking Arena 2008 Won by Indonesia||jmke||WebNews||0||10th November 2008 17:48|
|The TOP 3 MSI EU Overclocking Challenge battles in the Master Overclocking Arena 2008||jmke||WebNews||4||7th November 2008 13:23|
|MSI European Overclocking Challenge 2008||jmke||WebNews||1||6th July 2008 09:14|
|MSI Overclocking Contest : Info & Howto Join||jmke||Hardware Overclocking and Case Modding||1||14th June 2008 19:44|