Help overclocking DFI LanParty UT nF3 250GB - Page 2

26th November 2004, 21:56

Thank you all!

I changed some settings:

FSB Bus Freq: 229
AGP Bus Freq: 67
LDT/FSB Freq Ratio: 4
CPU/FSB Freq Ratio: 10.5
CPU VID: 1.50
CPU VID Special: 110%
Chipset Voltage: 1.8
AGP Voltage: 1.7
DRAM Voltage: 2.9

DRAM Freq Set: 200 (1/01)
CPC: Enabled
tCL: 3
tRCD: 4
tRAS: 10
tRP: 4
tRC: 11
tRFC: 14
tRRD: 2
tWR: 2
tWTR: 1
tRTW: 2
tREF: 3072 200 (3.9us)
tWCL: Auto
DQS Skew: Increase
DQS Skew Value: 64
DRAM Drive Strength: Level 1
Max Async Latency: 8
Read Preamble Time: 6
Idle Cycle Limit: 32
Dynamic Counter: Enabled
R/W Queue Bypass: 16
Bypass Max: 7
32 Byte Granulation: Enable (4burst)

CPU-Z shows following (see attached):

CPU Core Speed: 2405.5 MHz
Multiplier: 10.5
HTT: 229.1 MHz
Memory: 229.1 MHz

Any other suggestions? I can't push Memory over 229

Thx
DJ

30th November 2004, 00:34

Thanks.

This is where I am now and it works pretty good:

FSB Bus Frequency: 252
AGP Bus Frequency: 67
LDT/FSB Frequency Ratio: 3
CPU/FSB Frequency Ratio: 10
CPU VID Control: 1.525
CPU VID Special Control: 110%
Chipset Voltage Control: 1.6
AGP Voltage Control: 1.5
DRAM Voltage Control: 3.0

DRAM Frequency Set: 180 (9/10)
CPC: Disabled
tCL: 2.5
tRCD: 4
tRAS: 7
tRP: 4
tRC: 15
tRFC: 17
tRRD: 00
tWR: 3
tWTR: 2
tRTW: 4
tREF: 4708 166 (1.95us)
tWCL: Auto
DQS Skew: Increase
DQS Skew Value: 64
DRAM Drive Strength: Level 1
Max Async Latency: 8
Read Preamble Time: 6
Idle Cycle Limit: 32
Dynamic Counter: Disabled
R/W Queue Bypass: 16
Bypass Max: 4
32 Byte Granulation: Enable (4burst)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[M] DFI LANParty DK X58-T3eH9 Overclocking test	jmke	WebNews	0	9th February 2010 10:39
Best choice of Quad core overclocking, the DFI LANParty DK P35 T2RS shows off!	windwithme	Hardware Overclocking and Case Modding	5	15th December 2007 17:26
DFI LANPARTY UT NF4 Venus SLI Overclocking Tests	jmke	WebNews	0	22nd March 2006 16:15
TwinMOS on DFI Lanparty nf3 250gb	Juventino	Hardware/Software Problems, Bugs	7	9th May 2005 18:04
asus k8v se dlx vs dfi lanparty ut nf3 250gb	Juventino	Hardware/Software Problems, Bugs	4	18th April 2005 18:21
DFI LANParty UT nF3 250Gb	jmke	WebNews	0	11th February 2005 09:14
DFI LANPARTY UT nF3 250Gb Motherboard	jmke	WebNews	3	24th November 2004 07:00
DFI LANPARTY UT nF3 250Gb	Sidney	WebNews	0	6th November 2004 02:42
DFI LANParty UT nF3 250Gb Motherboard	jmke	WebNews	0	3rd November 2004 22:36
DFI LANParty UT nF3 250Gb Motherboard	Sidney	WebNews	2	3rd November 2004 12:10

26th November 2004, 21:56	#11
OldDarux Posts: n/a	Thank you all! I changed some settings: FSB Bus Freq: 229 AGP Bus Freq: 67 LDT/FSB Freq Ratio: 4 CPU/FSB Freq Ratio: 10.5 CPU VID: 1.50 CPU VID Special: 110% Chipset Voltage: 1.8 AGP Voltage: 1.7 DRAM Voltage: 2.9 DRAM Freq Set: 200 (1/01) CPC: Enabled tCL: 3 tRCD: 4 tRAS: 10 tRP: 4 tRC: 11 tRFC: 14 tRRD: 2 tWR: 2 tWTR: 1 tRTW: 2 tREF: 3072 200 (3.9us) tWCL: Auto DQS Skew: Increase DQS Skew Value: 64 DRAM Drive Strength: Level 1 Max Async Latency: 8 Read Preamble Time: 6 Idle Cycle Limit: 32 Dynamic Counter: Enabled R/W Queue Bypass: 16 Bypass Max: 7 32 Byte Granulation: Enable (4burst) CPU-Z shows following (see attached): CPU Core Speed: 2405.5 MHz Multiplier: 10.5 HTT: 229.1 MHz Memory: 229.1 MHz Any other suggestions? I can't push Memory over 229 Thx DJ

30th November 2004, 00:34	#12
OldDarux Posts: n/a	Thanks. This is where I am now and it works pretty good: FSB Bus Frequency: 252 AGP Bus Frequency: 67 LDT/FSB Frequency Ratio: 3 CPU/FSB Frequency Ratio: 10 CPU VID Control: 1.525 CPU VID Special Control: 110% Chipset Voltage Control: 1.6 AGP Voltage Control: 1.5 DRAM Voltage Control: 3.0 DRAM Frequency Set: 180 (9/10) CPC: Disabled tCL: 2.5 tRCD: 4 tRAS: 7 tRP: 4 tRC: 15 tRFC: 17 tRRD: 00 tWR: 3 tWTR: 2 tRTW: 4 tREF: 4708 166 (1.95us) tWCL: Auto DQS Skew: Increase DQS Skew Value: 64 DRAM Drive Strength: Level 1 Max Async Latency: 8 Read Preamble Time: 6 Idle Cycle Limit: 32 Dynamic Counter: Disabled R/W Queue Bypass: 16 Bypass Max: 4 32 Byte Granulation: Enable (4burst)