| Thread Tools |
2nd July 2002, 17:03 | #1 |
Posts: n/a
| Cutting in a Chieftec's Front Bezel Any suggestions? I read the guy @ Hexus (or Nexus, dunno), used a hacksaw (a small saw with a hand(vat) to cut in the plastic.. Problem is, I don't have a clue where to find a tool like that. I can't use a jigsaw coz that melts the plastic totally (tried it in my AOPen for a 92mm front blowhole and it was a mess) So, any idea how to cut the curvy front bezel (the flat part, the door in fact) so I have a clean space for a 4x20 vfd? (don't know the exact size, it's 4cm on 8 or so... (rectangular) |
2nd July 2002, 18:58 | #2 |
Posts: n/a
| sorry voor nederlands indien rechthoekige vorm zou ik het als volgt proberen : - een gat boren van 10mm (eerst 5mm, dan 10mm) op de plaats die ge weg wilt. - Daar past dan een zaagblad voor een ijzerzaag in. Manueel uitzagen met zo een zaagblad - Met schuurpapier beetje afwerken Op die manier ben je ook zeker dat het 100% recht is, en kan er nix wegsmelten :P |
2nd July 2002, 19:36 | #3 |
Posts: n/a
| mijn hand vertrouw ik toch niet voor 100% zekerheid op rechtheid toch bedankt voor de tip, maar die handzaag is exact wat die "hacksaw" is van die mannen van hexus... dus eigenlijk gewoon zo een ijzerzaagje, maar dan voor plastic brr, dat eerste gat boren in die deur gaat raar doen, we'll c |
2nd July 2002, 19:43 | #4 | |
Member Join Date: May 2002
Posts: 1,343
| Quote:
(calantak ende duron witnessed this ... stress ) | |
2nd July 2002, 20:02 | #5 | |
Posts: n/a
| Quote:
| |
2nd July 2002, 20:04 | #6 |
Posts: n/a
| achzo, ik zie net dat ik hacksaw en jigsaw verwarde sowwy :P enniweejz, die zaagbladen kosten 2x niets, de zaag op zich (die je voor plastic niet nodig zult hebben) ga je voor een 20€ wel kunnen vinden |
2nd July 2002, 20:12 | #7 |
Member Join Date: May 2002
Posts: 1,343
| rondom het gebied dat ge gaat uitsnijden niet vergeten goede tape aan te brengen Jas ... bij uitschuiver gaat u da toch wel wa schade besparen |
2nd July 2002, 20:35 | #8 |
[M] Reviewer Join Date: May 2002
Posts: 1,186
| how about using a dremel on lowest speed? |
3rd July 2002, 06:38 | #9 | |
Posts: n/a
| Quote:
@Bicker: ik heb geen dremel, en kheb al verhalen genoeg gehoord van smeltend plastic | |
3rd July 2002, 12:42 | #10 |
Posts: n/a
| dremel on low speed also melts the plastic |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ASRock introduces world’s first AMD front USB 3.0 capable boards | jmke | WebNews | 0 | 24th July 2010 09:09 |
AMD Eyefinity Bezel Management Software Coming Next Year | jmke | WebNews | 0 | 2nd December 2009 11:45 |
SilverStone 3.5” Card reader front I/O panel (FP34) | jmke | WebNews | 0 | 2nd August 2006 09:39 |
MSI K8N Diamond Plus with Vacuum Tube Front Panel and Opteron 144 | windwithme | Hardware Overclocking and Case Modding | 2 | 28th January 2006 11:57 |
Front panels connectors on case | crakajax | General Madness - System Building Advice | 1 | 10th September 2005 03:18 |
Multi-Function Front Panel Shootout | Da_BoKa | WebNews | 0 | 9th June 2005 16:07 |
FRONTX Front Panel Computer Port System | Da_BoKa | WebNews | 0 | 28th January 2005 08:39 |
Front X-tension Review | jmke | WebNews | 0 | 15th December 2004 16:19 |
Multiple Front Side Buses; Coming to an Intel Server Near You | jmke | WebNews | 0 | 6th November 2004 15:49 |
Thread Tools | |
| |