Follow us on Twitter
Follow us on Facebook
How to Cool your PC with Dry Ice
A complete guide by on working with Dry Ice so you can reach sub zero temperatures with your CPU and graphics card. Details on building containers, where to buy Dry Ice and important tips and tricks.
Insulation
I’ve used 1.5cm think insulation of Armaflex, there are many types of insulation but the best is closed sell foam. This means no air can go through it.
Once you strapped the container in insulation, you need to do some work on the motherboard, to make sure no condensation can form during your benching marking run, and possible spoil the fun… and your hardware. I used layers of 1cm Armaflex to create the following:
If you want to go the extra mile you apply some none conductive grease onto the motherboard to prevent condensation completely!
When everything insulated it’s time for the final preparation steps, lapping or sanding down the container: to improve contact with the CPU. Use grid 250-400 to remove all scratches, and then work up with 500-600-800 till grid 1000. After that it should be perfectly flat. You can polish your base for that extra little *bling* effect. .
Now you’re ready to install the container ->
Once you strapped the container in insulation, you need to do some work on the motherboard, to make sure no condensation can form during your benching marking run, and possible spoil the fun… and your hardware. I used layers of 1cm Armaflex to create the following:
If you want to go the extra mile you apply some none conductive grease onto the motherboard to prevent condensation completely!
When everything insulated it’s time for the final preparation steps, lapping or sanding down the container: to improve contact with the CPU. Use grid 250-400 to remove all scratches, and then work up with 500-600-800 till grid 1000. After that it should be perfectly flat. You can polish your base for that extra little *bling* effect. .
Now you’re ready to install the container ->
Comment
from jmke
@ 2005/05/08
you can read more about Jort's Dry Ice and LN² adventures over here: http://www.madshrimps.be/forums/show...threadid=12169
Comment
from
@ 2005/05/08
PRAXAIR, Nijverheidsstraat 4, 2260 OEVEL
their truck rides out to pick it up on friday, they store it over weekend and make the necessary deliveries first thing monday morning. So, friday and monday is your best bet but since most people will be doing this in the weekend, it's best to call them and have them keep some aside for you to pick up on friday.
I have the phone number here somewhere, if I find it, I'll post it.
normally I don't read a whole review/howto but for jort's article, I've made an exception
their truck rides out to pick it up on friday, they store it over weekend and make the necessary deliveries first thing monday morning. So, friday and monday is your best bet but since most people will be doing this in the weekend, it's best to call them and have them keep some aside for you to pick up on friday.
I have the phone number here somewhere, if I find it, I'll post it.
normally I don't read a whole review/howto but for jort's article, I've made an exception
Comment
from
@ 2005/05/08
Praxair Dep. KEMPEN
Nijverheidsstraat 4
2260 OEVEL 014/25 06 03
Nijverheidsstraat 4
2260 OEVEL 014/25 06 03
Comment
from
@ 2005/05/08
way to go to the editor
and tnx kristos for reading it and correcting a bit
and tnx kristos for reading it and correcting a bit
Comment
from
@ 2005/05/08
the material that i am now using is ertalite or hd-1000 named.
this is something nobody know's, when tim was on the way to here i tested the plexi with ln² and a hammer. it was not breaking.
i think because the plexi was in direct contact with the container and the pressure due the screws it cracks.
so if you use plexi for holddown you should see the plexi doesn't make contact with the baseplate or tube and it w'll be oke
greetz
this is something nobody know's, when tim was on the way to here i tested the plexi with ln² and a hammer. it was not breaking.
i think because the plexi was in direct contact with the container and the pressure due the screws it cracks.
so if you use plexi for holddown you should see the plexi doesn't make contact with the baseplate or tube and it w'll be oke
greetz
Comment
from
@ 2005/05/09
Why didn't you just solder the copper?
Comment
from
@ 2005/05/09
due the extreme temps the solder can crack.
some people do solder it because they don't have the equipment to do, but i DONT recommend soldering
some people do solder it because they don't have the equipment to do, but i DONT recommend soldering
Comment
from
@ 2005/05/18
Comment
from
@ 2005/05/18
here is another one
http://www.hoekloos.be/International...oc_antwerpen02
Quote:
|
Originally posted by kristos Praxair Dep. KEMPEN Nijverheidsstraat 4 2260 OEVEL 014/25 06 03 |
http://www.hoekloos.be/International...oc_antwerpen02
Comment
from
@ 2005/05/18
for the dutchies
www.droogijs.nl
for the English
http://www.droogijs.nl/engels/index.html
20 of may i will be talking with that compagie to get some reduction and make a MADreview
Not into depth but just going like mad :grin:
only results will count
just warming up my hardware for the coming cascade rig
www.droogijs.nl
for the English
http://www.droogijs.nl/engels/index.html
20 of may i will be talking with that compagie to get some reduction and make a MADreview
Not into depth but just going like mad :grin:
only results will count
just warming up my hardware for the coming cascade rig
Comment
from
@ 2005/05/18
Comment
from
@ 2005/05/18
cool
Quote:
|
Originally posted by petervandamned for the dutchies www.droogijs.nl for the English http://www.droogijs.nl/engels/index.html 20 of may i will be talking with that compagie to get some reduction and make a MADreview Not into depth but just going like mad :grin: only results will count just warming up my hardware for the coming cascade rig |
cool
Comment
from
@ 2005/05/18
where you going to get your container 
Comment
from
@ 2005/05/23
http://www.ysfab.be/nl/contact.asp
dry ice availeble here too
dry ice availeble here too
Quote:
| 7.5 euro voor 10 kilo, Blokken, pellets of slices. |
Comment
from
@ 2005/06/08
Got me some dry ice from ijsblokjes.be, hopefully everything will turn out alright 
Comment
from
@ 2005/06/08
Ok, going good here .
.
Comment
from
@ 2005/06/08
-37:grr:
got some mhz result?
good luck
got some mhz result?
good luck
Comment
from
@ 2005/06/08
Can't get past 3120 MHz :grum:
Comment
from
@ 2005/06/08
-37°C looks nice, pics of HW setup?
Comment
from
@ 2005/06/08
Tonight
Copyright © 2001-2011 Madshrimps, All rights reserved.
Graphic Design by Dennis Kestelle, Programming by Maarten Menten,
Overall Site design by John Meys
All information and graphics contained in Madshrimps are sole property of the Madshrimps crew and may not be reproduced or copied in any manner without written permission from us.
